| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_log: validate MAC header was set before dumping it
The fallback path of dump_mac_header() guards the MAC header access
only with "skb->mac_header != skb->network_header", without checking
skb_mac_header_was_set(). When the MAC header is unset, mac_header is
0xffff, so the test passes and skb_mac_header(skb) returns
skb->head + 0xffff, ~64 KiB past the buffer; the loop then reads
dev->hard_header_len bytes out of bounds into the kernel log.
This is reachable via the netdev logger: nf_log_unknown_packet() calls
dump_mac_header() unconditionally, and an skb sent through AF_PACKET
with PACKET_QDISC_BYPASS reaches the egress hook with mac_header still
unset (__dev_queue_xmit(), which would reset it, is bypassed).
Add the skb_mac_header_was_set() check the ARPHRD_ETHER path already
uses, and replace the open-coded MAC header length test with
skb_mac_header_len(). Only skbs with an unset MAC header are affected;
valid ones are dumped as before.
BUG: KASAN: slab-out-of-bounds in dump_mac_header (net/netfilter/nf_log_syslog.c:831)
Read of size 1 at addr ffff88800ea49d3f by task exploit/148
Call Trace:
kasan_report (mm/kasan/report.c:595)
dump_mac_header (net/netfilter/nf_log_syslog.c:831)
nf_log_netdev_packet (net/netfilter/nf_log_syslog.c:938 net/netfilter/nf_log_syslog.c:963)
nf_log_packet (net/netfilter/nf_log.c:260)
nft_log_eval (net/netfilter/nft_log.c:60)
nft_do_chain (net/netfilter/nf_tables_core.c:285)
nft_do_chain_netdev (net/netfilter/nft_chain_filter.c:307)
nf_hook_slow (net/netfilter/core.c:619)
nf_hook_direct_egress (net/packet/af_packet.c:257)
packet_xmit (net/packet/af_packet.c:280)
packet_sendmsg (net/packet/af_packet.c:3114)
__sys_sendto (net/socket.c:2265) |
| In the Linux kernel, the following vulnerability has been resolved:
eventpoll: fix ep_remove struct eventpoll / struct file UAF
ep_remove() (via ep_remove_file()) cleared file->f_ep under
file->f_lock but then kept using @file inside the critical section
(is_file_epoll(), hlist_del_rcu() through the head, spin_unlock).
A concurrent __fput() taking the eventpoll_release() fastpath in
that window observed the transient NULL, skipped
eventpoll_release_file() and ran to f_op->release / file_free().
For the epoll-watches-epoll case, f_op->release is
ep_eventpoll_release() -> ep_clear_and_put() -> ep_free(), which
kfree()s the watched struct eventpoll. Its embedded ->refs
hlist_head is exactly where epi->fllink.pprev points, so the
subsequent hlist_del_rcu()'s "*pprev = next" scribbles into freed
kmalloc-192 memory.
In addition, struct file is SLAB_TYPESAFE_BY_RCU, so the slot
backing @file could be recycled by alloc_empty_file() --
reinitializing f_lock and f_ep -- while ep_remove() is still
nominally inside that lock. The upshot is an attacker-controllable
kmem_cache_free() against the wrong slab cache.
Pin @file via epi_fget() at the top of ep_remove() and gate the
critical section on the pin succeeding. With the pin held @file
cannot reach refcount zero, which holds __fput() off and
transitively keeps the watched struct eventpoll alive across the
hlist_del_rcu() and the f_lock use, closing both UAFs.
If the pin fails @file has already reached refcount zero and its
__fput() is in flight. Because we bailed before clearing f_ep,
that path takes the eventpoll_release() slow path into
eventpoll_release_file() and blocks on ep->mtx until the waiter
side's ep_clear_and_put() drops it. The bailed epi's share of
ep->refcount stays intact, so the trailing ep_refcount_dec_and_test()
in ep_clear_and_put() cannot free the eventpoll out from under
eventpoll_release_file(); the orphaned epi is then cleaned up
there.
A successful pin also proves we are not racing
eventpoll_release_file() on this epi, so drop the now-redundant
re-check of epi->dying under f_lock. The cheap lockless
READ_ONCE(epi->dying) fast-path bailout stays. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet-tcp: fix race between ICReq handling and queue teardown
nvmet_tcp_handle_icreq() updates queue->state after sending an
Initialization Connection Response (ICResp), but it does so without
serializing against target-side queue teardown.
If an NVMe/TCP host sends an Initialization Connection Request
(ICReq) and immediately closes the connection, target-side teardown
may start in softirq context before io_work drains the already
buffered ICReq. In that case, nvmet_tcp_schedule_release_queue()
sets queue->state to NVMET_TCP_Q_DISCONNECTING and drops the queue
reference under state_lock.
If io_work later processes that ICReq, nvmet_tcp_handle_icreq() can
still overwrite the state back to NVMET_TCP_Q_LIVE. That defeats the
DISCONNECTING-state guard in nvmet_tcp_schedule_release_queue() and
allows a later socket state change to re-enter teardown and issue a
second kref_put() on an already released queue.
The ICResp send failure path has the same problem. If teardown has
already moved the queue to DISCONNECTING, a send error can still
overwrite the state with NVMET_TCP_Q_FAILED, again reopening the
window for a second teardown path to drop the queue reference.
Fix this by serializing both post-send state transitions with
state_lock and bailing out if teardown has already started.
Use -ESHUTDOWN as an internal sentinel for that bail-out path rather
than propagating it as a transport error like -ECONNRESET. Keep
nvmet_tcp_socket_error() setting rcv_state to NVMET_TCP_RECV_ERR before
honoring that sentinel so receive-side parsing stays quiesced until the
existing release path completes. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: defensively unhash xfrm_state lists in __xfrm_state_delete
KASAN reproduces a slab-use-after-free in __xfrm_state_delete()'s
hlist_del_rcu calls under syzkaller load on linux-6.12.y stable
(reproduced on 6.12.47, also reachable via the same code path on
torvalds/master and on the ipsec tree). Nine unique signatures cluster
in the xfrm_state lifecycle, the load-bearing one being:
BUG: KASAN: slab-use-after-free in __hlist_del include/linux/list.h:990 [inline]
BUG: KASAN: slab-use-after-free in hlist_del_rcu include/linux/rculist.h:516 [inline]
BUG: KASAN: slab-use-after-free in __xfrm_state_delete net/xfrm/xfrm_state.c
Write of size 8 at addr ffff8881198bcb70 by task kworker/u8:9/435
Workqueue: netns cleanup_net
Call Trace:
__hlist_del / hlist_del_rcu
__xfrm_state_delete
xfrm_state_delete
xfrm_state_flush
xfrm_state_fini
ops_exit_list
cleanup_net
The other observed signatures hit the same slab object from
__xfrm_state_lookup, xfrm_alloc_spi, __xfrm_state_insert and an OOB
write variant of __xfrm_state_delete, all on the byseq/byspi
hash chains.
__xfrm_state_delete() guards its byseq and byspi unhashes with
value-based predicates:
if (x->km.seq)
hlist_del_rcu(&x->byseq);
if (x->id.spi)
hlist_del_rcu(&x->byspi);
while everywhere else in the file (e.g. state_cache, state_cache_input)
the safer hlist_unhashed() check is used. xfrm_alloc_spi() sets
x->id.spi = newspi inside xfrm_state_lock and then immediately inserts
into byspi, but a path that observes x->id.spi != 0 outside of
xfrm_state_lock can still skip-or-hit the byspi unhash inconsistently
with whether x is actually on the list. The same holds for x->km.seq
versus byseq, and the bydst/bysrc unhashes have no predicate at all,
so a second __xfrm_state_delete() on the same object writes through
LIST_POISON pprev.
The defensive change here:
- Use hlist_del_init_rcu() instead of hlist_del_rcu() on bydst,
bysrc, byseq and byspi so a second deletion is a no-op rather
than a write through LIST_POISON pprev. The byseq/byspi nodes
are already initialised in xfrm_state_alloc().
- Test hlist_unhashed() rather than the value predicate for
byseq/byspi, so the unhash decision tracks list state rather than
mutable scalar fields.
Empirical verification: applied this patch on top of v6.12.47, rebuilt,
and re-ran the same syzkaller harness for 1h16m on a previously-crashy
configuration that produced ~100 hits each of slab-use-after-free
Read in xfrm_alloc_spi / Read in __xfrm_state_lookup / Write in
__xfrm_state_delete. After the patch, 7.1M execs across 32 VMs at
~1550 exec/sec produced zero xfrm_state UAF/OOB hits. /proc/slabinfo
confirms the xfrm_state slab is actively allocated and freed during
the run (~143 KiB resident), so the fuzzer is still exercising those
code paths -- they just no longer crash.
Reproduction:
- Linux 6.12.47 x86_64 + KASAN_GENERIC + KASAN_INLINE + KCOV
- syzkaller @ 746545b8b1e4c3a128db8652b340d3df90ce61db
- 32 QEMU/KVM VMs x 2 vCPU on AWS c5.metal bare metal
- 9 unique signatures collected in ~9h, all within xfrm_state
lifecycle |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Clear Present bit before tearing down context entry
When tearing down a context entry, the current implementation zeros the
entire 128-bit entry using multiple 64-bit writes. This creates a window
where the hardware can fetch a "torn" entry — where some fields are
already zeroed while the 'Present' bit is still set — leading to
unpredictable behavior or spurious faults.
While x86 provides strong write ordering, the compiler may reorder writes
to the two 64-bit halves of the context entry. Even without compiler
reordering, the hardware fetch is not guaranteed to be atomic with
respect to multiple CPU writes.
Align with the "Guidance to Software for Invalidations" in the VT-d spec
(Section 6.5.3.3) by implementing the recommended ownership handshake:
1. Clear only the 'Present' (P) bit of the context entry first to
signal the transition of ownership from hardware to software.
2. Use dma_wmb() to ensure the cleared bit is visible to the IOMMU.
3. Perform the required cache and context-cache invalidation to ensure
hardware no longer has cached references to the entry.
4. Fully zero out the entry only after the invalidation is complete.
Also, add a dma_wmb() to context_set_present() to ensure the entry
is fully initialized before the 'Present' bit becomes visible. |
| In the Linux kernel, the following vulnerability has been resolved:
rtmutex: Use waiter::task instead of current in remove_waiter()
remove_waiter() is used by the slowlock paths, but it is also used for
proxy-lock rollback in rt_mutex_start_proxy_lock() when invoked from
futex_requeue().
In the latter case waiter::task is not current, but remove_waiter()
operates on current for the dequeue operation. That results in several
problems:
1) the rbtree dequeue happens without waiter::task::pi_lock being held
2) the waiter task's pi_blocked_on state is not cleared, which leaves a
dangling pointer primed for UAF around.
3) rt_mutex_adjust_prio_chain() operates on the wrong top priority waiter
task
Use waiter::task instead of current in all related operations in
remove_waiter() to cure those problems.
[ tglx: Fixup rt_mutex_adjust_prio_chain(), add a comment and amend the
changelog ] |
| In the Linux kernel, the following vulnerability has been resolved:
bonding: fix type confusion in bond_setup_by_slave()
kernel BUG at net/core/skbuff.c:2306!
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
RIP: 0010:pskb_expand_head+0xa08/0xfe0 net/core/skbuff.c:2306
RSP: 0018:ffffc90004aff760 EFLAGS: 00010293
RAX: 0000000000000000 RBX: ffff88807e3c8780 RCX: ffffffff89593e0e
RDX: ffff88807b7c4900 RSI: ffffffff89594747 RDI: ffff88807b7c4900
RBP: 0000000000000820 R08: 0000000000000005 R09: 0000000000000000
R10: 00000000961a63e0 R11: 0000000000000000 R12: ffff88807e3c8780
R13: 00000000961a6560 R14: dffffc0000000000 R15: 00000000961a63e0
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fe1a0ed8df0 CR3: 000000002d816000 CR4: 00000000003526f0
Call Trace:
<TASK>
ipgre_header+0xdd/0x540 net/ipv4/ip_gre.c:900
dev_hard_header include/linux/netdevice.h:3439 [inline]
packet_snd net/packet/af_packet.c:3028 [inline]
packet_sendmsg+0x3ae5/0x53c0 net/packet/af_packet.c:3108
sock_sendmsg_nosec net/socket.c:727 [inline]
__sock_sendmsg net/socket.c:742 [inline]
____sys_sendmsg+0xa54/0xc30 net/socket.c:2592
___sys_sendmsg+0x190/0x1e0 net/socket.c:2646
__sys_sendmsg+0x170/0x220 net/socket.c:2678
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x106/0xf80 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fe1a0e6c1a9
When a non-Ethernet device (e.g. GRE tunnel) is enslaved to a bond,
bond_setup_by_slave() directly copies the slave's header_ops to the
bond device:
bond_dev->header_ops = slave_dev->header_ops;
This causes a type confusion when dev_hard_header() is later called
on the bond device. Functions like ipgre_header(), ip6gre_header(),all use
netdev_priv(dev) to access their device-specific private data. When
called with the bond device, netdev_priv() returns the bond's private
data (struct bonding) instead of the expected type (e.g. struct
ip_tunnel), leading to garbage values being read and kernel crashes.
Fix this by introducing bond_header_ops with wrapper functions that
delegate to the active slave's header_ops using the slave's own
device. This ensures netdev_priv() in the slave's header functions
always receives the correct device.
The fix is placed in the bonding driver rather than individual device
drivers, as the root cause is bond blindly inheriting header_ops from
the slave without considering that these callbacks expect a specific
netdev_priv() layout.
The type confusion can be observed by adding a printk in
ipgre_header() and running the following commands:
ip link add dummy0 type dummy
ip addr add 10.0.0.1/24 dev dummy0
ip link set dummy0 up
ip link add gre1 type gre local 10.0.0.1
ip link add bond1 type bond mode active-backup
ip link set gre1 master bond1
ip link set gre1 up
ip link set bond1 up
ip addr add fe80::1/64 dev bond1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: Drop the lock in skb_may_tx_timestamp()
skb_may_tx_timestamp() may acquire sock::sk_callback_lock. The lock must
not be taken in IRQ context, only softirq is okay. A few drivers receive
the timestamp via a dedicated interrupt and complete the TX timestamp
from that handler. This will lead to a deadlock if the lock is already
write-locked on the same CPU.
Taking the lock can be avoided. The socket (pointed by the skb) will
remain valid until the skb is released. The ->sk_socket and ->file
member will be set to NULL once the user closes the socket which may
happen before the timestamp arrives.
If we happen to observe the pointer while the socket is closing but
before the pointer is set to NULL then we may use it because both
pointer (and the file's cred member) are RCU freed.
Drop the lock. Use READ_ONCE() to obtain the individual pointer. Add a
matching WRITE_ONCE() where the pointer are cleared. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: annotate data-races around hdev->req_status
__hci_cmd_sync_sk() sets hdev->req_status under hdev->req_lock:
hdev->req_status = HCI_REQ_PEND;
However, several other functions read or write hdev->req_status without
holding any lock:
- hci_send_cmd_sync() reads req_status in hci_cmd_work (workqueue)
- hci_cmd_sync_complete() reads/writes from HCI event completion
- hci_cmd_sync_cancel() / hci_cmd_sync_cancel_sync() read/write
- hci_abort_conn() reads in connection abort path
Since __hci_cmd_sync_sk() runs on hdev->req_workqueue while
hci_send_cmd_sync() runs on hdev->workqueue, these are different
workqueues that can execute concurrently on different CPUs. The plain
C accesses constitute a data race.
Add READ_ONCE()/WRITE_ONCE() annotations on all concurrent accesses
to hdev->req_status to prevent potential compiler optimizations that
could affect correctness (e.g., load fusing in the wait_event
condition or store reordering). |
| In the Linux kernel, the following vulnerability has been resolved:
writeback: Fix use after free in inode_switch_wbs_work_fn()
inode_switch_wbs_work_fn() has a loop like:
wb_get(new_wb);
while (1) {
list = llist_del_all(&new_wb->switch_wbs_ctxs);
/* Nothing to do? */
if (!list)
break;
... process the items ...
}
Now adding of items to the list looks like:
wb_queue_isw()
if (llist_add(&isw->list, &wb->switch_wbs_ctxs))
queue_work(isw_wq, &wb->switch_work);
Because inode_switch_wbs_work_fn() loops when processing isw items, it
can happen that wb->switch_work is pending while wb->switch_wbs_ctxs is
empty. This is a problem because in that case wb can get freed (no isw
items -> no wb reference) while the work is still pending causing
use-after-free issues.
We cannot just fix this by cancelling work when freeing wb because that
could still trigger problematic 0 -> 1 transitions on wb refcount due to
wb_get() in inode_switch_wbs_work_fn(). It could be all handled with
more careful code but that seems unnecessarily complex so let's avoid
that until it is proven that the looping actually brings practical
benefit. Just remove the loop from inode_switch_wbs_work_fn() instead.
That way when wb_queue_isw() queues work, we are guaranteed we have
added the first item to wb->switch_wbs_ctxs and nobody is going to
remove it (and drop the wb reference it holds) until the queued work
runs. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix mechToken leak when SPNEGO decode fails after token alloc
The kernel ASN.1 BER decoder calls action callbacks incrementally as it
walks the input. When ksmbd_decode_negTokenInit() reaches the mechToken
[2] OCTET STRING element, ksmbd_neg_token_alloc() allocates
conn->mechToken immediately via kmemdup_nul(). If a later element in
the same blob is malformed, then the decoder will return nonzero after
the allocation is already live. This could happen if mechListMIC [3]
overrunse the enclosing SEQUENCE.
decode_negotiation_token() then sets conn->use_spnego = false because
both the negTokenInit and negTokenTarg grammars failed. The cleanup at
the bottom of smb2_sess_setup() is gated on use_spnego:
if (conn->use_spnego && conn->mechToken) {
kfree(conn->mechToken);
conn->mechToken = NULL;
}
so the kfree is skipped, causing the mechToken to never be freed.
This codepath is reachable pre-authentication, so untrusted clients can
cause slow memory leaks on a server without even being properly
authenticated.
Fix this up by not checking check for use_spnego, as it's not required,
so the memory will always be properly freed. At the same time, always
free the memory in ksmbd_conn_free() incase some other failure path
forgot to free it. |
| In the Linux kernel, the following vulnerability has been resolved:
team: fix header_ops type confusion with non-Ethernet ports
Similar to commit 950803f72547 ("bonding: fix type confusion in
bond_setup_by_slave()") team has the same class of header_ops type
confusion.
For non-Ethernet ports, team_setup_by_port() copies port_dev->header_ops
directly. When the team device later calls dev_hard_header() or
dev_parse_header(), these callbacks can run with the team net_device
instead of the real lower device, so netdev_priv(dev) is interpreted as
the wrong private type and can crash.
The syzbot report shows a crash in bond_header_create(), but the root
cause is in team: the topology is gre -> bond -> team, and team calls
the inherited header_ops with its own net_device instead of the lower
device, so bond_header_create() receives a team device and interprets
netdev_priv() as bonding private data, causing a type confusion crash.
Fix this by introducing team header_ops wrappers for create/parse,
selecting a team port under RCU, and calling the lower device callbacks
with port->dev, so each callback always sees the correct net_device
context.
Also pass the selected lower device to the lower parse callback, so
recursion is bounded in stacked non-Ethernet topologies and parse
callbacks always run with the correct device context. |
| In the Linux kernel, the following vulnerability has been resolved:
bonding: prevent potential infinite loop in bond_header_parse()
bond_header_parse() can loop if a stack of two bonding devices is setup,
because skb->dev always points to the hierarchy top.
Add new "const struct net_device *dev" parameter to
(struct header_ops)->parse() method to make sure the recursion
is bounded, and that the final leaf parse method is called. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: handle attr_set_size() errors when truncating files
If attr_set_size() fails while truncating down, the error is silently
ignored and the inode may be left in an inconsistent state. |
| In the Linux kernel, the following vulnerability has been resolved:
fs: quota: create dedicated workqueue for quota_release_work
There is a kernel panic due to WARN_ONCE when panic_on_warn is set.
This issue occurs when writeback is triggered due to sync call for an
opened file(ie, writeback reason is WB_REASON_SYNC). When f2fs balance
is needed at sync path, flush for quota_release_work is triggered.
By default quota_release_work is queued to "events_unbound" queue which
does not have WQ_MEM_RECLAIM flag. During f2fs balance "writeback"
workqueue tries to flush quota_release_work causing kernel panic due to
MEM_RECLAIM flag mismatch errors.
This patch creates dedicated workqueue with WQ_MEM_RECLAIM flag
for work quota_release_work.
------------[ cut here ]------------
WARNING: CPU: 4 PID: 14867 at kernel/workqueue.c:3721 check_flush_dependency+0x13c/0x148
Call trace:
check_flush_dependency+0x13c/0x148
__flush_work+0xd0/0x398
flush_delayed_work+0x44/0x5c
dquot_writeback_dquots+0x54/0x318
f2fs_do_quota_sync+0xb8/0x1a8
f2fs_write_checkpoint+0x3cc/0x99c
f2fs_gc+0x190/0x750
f2fs_balance_fs+0x110/0x168
f2fs_write_single_data_page+0x474/0x7dc
f2fs_write_data_pages+0x7d0/0xd0c
do_writepages+0xe0/0x2f4
__writeback_single_inode+0x44/0x4ac
writeback_sb_inodes+0x30c/0x538
wb_writeback+0xf4/0x440
wb_workfn+0x128/0x5d4
process_scheduled_works+0x1c4/0x45c
worker_thread+0x32c/0x3e8
kthread+0x11c/0x1b0
ret_from_fork+0x10/0x20
Kernel panic - not syncing: kernel: panic_on_warn set ... |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: ccp - Always pass in an error pointer to __sev_platform_shutdown_locked()
When
9770b428b1a2 ("crypto: ccp - Move dev_info/err messages for SEV/SNP init and shutdown")
moved the error messages dumping so that they don't need to be issued by
the callers, it missed the case where __sev_firmware_shutdown() calls
__sev_platform_shutdown_locked() with a NULL argument which leads to
a NULL ptr deref on the shutdown path, during suspend to disk:
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: Oops: 0000 [#1] SMP NOPTI
CPU: 0 UID: 0 PID: 983 Comm: hib.sh Not tainted 6.17.0-rc4+ #1 PREEMPT(voluntary)
Hardware name: Supermicro Super Server/H12SSL-i, BIOS 2.5 09/08/2022
RIP: 0010:__sev_platform_shutdown_locked.cold+0x0/0x21 [ccp]
That rIP is:
00000000000006fd <__sev_platform_shutdown_locked.cold>:
6fd: 8b 13 mov (%rbx),%edx
6ff: 48 8b 7d 00 mov 0x0(%rbp),%rdi
703: 89 c1 mov %eax,%ecx
Code: 74 05 31 ff 41 89 3f 49 8b 3e 89 ea 48 c7 c6 a0 8e 54 a0 41 bf 92 ff ff ff e8 e5 2e 09 e1 c6 05 2a d4 38 00 01 e9 26 af ff ff <8b> 13 48 8b 7d 00 89 c1 48 c7 c6 18 90 54 a0 89 44 24 04 e8 c1 2e
RSP: 0018:ffffc90005467d00 EFLAGS: 00010282
RAX: 00000000ffffff92 RBX: 0000000000000000 RCX: 0000000000000000
^^^^^^^^^^^^^^^^
and %rbx is nice and clean.
Call Trace:
<TASK>
__sev_firmware_shutdown.isra.0
sev_dev_destroy
psp_dev_destroy
sp_destroy
pci_device_shutdown
device_shutdown
kernel_power_off
hibernate.cold
state_store
kernfs_fop_write_iter
vfs_write
ksys_write
do_syscall_64
entry_SYSCALL_64_after_hwframe
Pass in a pointer to the function-local error var in the caller.
With that addressed, suspending the ccp shows the error properly at
least:
ccp 0000:47:00.1: sev command 0x2 timed out, disabling PSP
ccp 0000:47:00.1: SEV: failed to SHUTDOWN error 0x0, rc -110
SEV-SNP: Leaking PFN range 0x146800-0x146a00
SEV-SNP: PFN 0x146800 unassigned, dumping non-zero entries in 2M PFN region: [0x146800 - 0x146a00]
...
ccp 0000:47:00.1: SEV-SNP firmware shutdown failed, rc -16, error 0x0
ACPI: PM: Preparing to enter system sleep state S5
kvm: exiting hardware virtualization
reboot: Power down
Btw, this driver is crying to be cleaned up to pass in a proper I/O
struct which can be used to store information between the different
functions, otherwise stuff like that will happen in the future again. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: ccp - Fix dereferencing uninitialized error pointer
Fix below smatch warnings:
drivers/crypto/ccp/sev-dev.c:1312 __sev_platform_init_locked()
error: we previously assumed 'error' could be null |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: mcast: Delay put pmc->idev in mld_del_delrec()
pmc->idev is still used in ip6_mc_clear_src(), so as mld_clear_delrec()
does, the reference should be put after ip6_mc_clear_src() return. |
| In the Linux kernel, the following vulnerability has been resolved:
eventpoll: don't decrement ep refcount while still holding the ep mutex
Jann Horn points out that epoll is decrementing the ep refcount and then
doing a
mutex_unlock(&ep->mtx);
afterwards. That's very wrong, because it can lead to a use-after-free.
That pattern is actually fine for the very last reference, because the
code in question will delay the actual call to "ep_free(ep)" until after
it has unlocked the mutex.
But it's wrong for the much subtler "next to last" case when somebody
*else* may also be dropping their reference and free the ep while we're
still using the mutex.
Note that this is true even if that other user is also using the same ep
mutex: mutexes, unlike spinlocks, can not be used for object ownership,
even if they guarantee mutual exclusion.
A mutex "unlock" operation is not atomic, and as one user is still
accessing the mutex as part of unlocking it, another user can come in
and get the now released mutex and free the data structure while the
first user is still cleaning up.
See our mutex documentation in Documentation/locking/mutex-design.rst,
in particular the section [1] about semantics:
"mutex_unlock() may access the mutex structure even after it has
internally released the lock already - so it's not safe for
another context to acquire the mutex and assume that the
mutex_unlock() context is not using the structure anymore"
So if we drop our ep ref before the mutex unlock, but we weren't the
last one, we may then unlock the mutex, another user comes in, drops
_their_ reference and releases the 'ep' as it now has no users - all
while the mutex_unlock() is still accessing it.
Fix this by simply moving the ep refcount dropping to outside the mutex:
the refcount itself is atomic, and doesn't need mutex protection (that's
the whole _point_ of refcounts: unlike mutexes, they are inherently
about object lifetimes). |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: Ignore too large handle values in BIG
hci_le_big_sync_established_evt is necessary to filter out cases where the
handle value is belonging to ida id range, otherwise ida will be erroneously
released in hci_conn_cleanup. |
