| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: lpfc: Fix memory leak in lpfc_create_port()
Commit 5e633302ace1 ("scsi: lpfc: vmid: Add support for VMID in mailbox
command") introduced allocations for the VMID resources in
lpfc_create_port() after the call to scsi_host_alloc(). Upon failure on the
VMID allocations, the new code would branch to the 'out' label, which
returns NULL without unwinding anything, thus skipping the call to
scsi_host_put().
Fix the problem by creating a separate label 'out_free_vmid' to unwind the
VMID resources and make the 'out_put_shost' label call only
scsi_host_put(), as was done before the introduction of allocations for
VMID. |
| In the Linux kernel, the following vulnerability has been resolved:
ipu3-imgu: Fix NULL pointer dereference in imgu_subdev_set_selection()
Calling v4l2_subdev_get_try_crop() and v4l2_subdev_get_try_compose()
with a subdev state of NULL leads to a NULL pointer dereference. This
can currently happen in imgu_subdev_set_selection() when the state
passed in is NULL, as this method first gets pointers to both the "try"
and "active" states and only then decides which to use.
The same issue has been addressed for imgu_subdev_get_selection() with
commit 30d03a0de650 ("ipu3-imgu: Fix NULL pointer dereference in active
selection access"). However the issue still persists in
imgu_subdev_set_selection().
Therefore, apply a similar fix as done in the aforementioned commit to
imgu_subdev_set_selection(). To keep things a bit cleaner, introduce
helper functions for "crop" and "compose" access and use them in both
imgu_subdev_set_selection() and imgu_subdev_get_selection(). |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/restrack: Release MR restrack when delete
The MR restrack also needs to be released when delete it, otherwise it
cause memory leak as the task struct won't be released. |
| In the Linux kernel, the following vulnerability has been resolved:
udmabuf: Set ubuf->sg = NULL if the creation of sg table fails
When userspace tries to map the dmabuf and if for some reason
(e.g. OOM) the creation of the sg table fails, ubuf->sg needs to be
set to NULL. Otherwise, when the userspace subsequently closes the
dmabuf fd, we'd try to erroneously free the invalid sg table from
release_udmabuf resulting in the following crash reported by syzbot:
general protection fault, probably for non-canonical address
0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 0 PID: 3609 Comm: syz-executor487 Not tainted
5.19.0-syzkaller-13930-g7ebfc85e2cd7 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 07/22/2022
RIP: 0010:dma_unmap_sgtable include/linux/dma-mapping.h:378 [inline]
RIP: 0010:put_sg_table drivers/dma-buf/udmabuf.c:89 [inline]
RIP: 0010:release_udmabuf+0xcb/0x4f0 drivers/dma-buf/udmabuf.c:114
Code: 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 2b 04 00 00 48 8d 7d 0c 4c
8b 63 30 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <0f> b6 14
02 48 89 f8 83 e0 07 83 c0 03 38 d0 7c 08 84 d2 0f 85 e2
RSP: 0018:ffffc900037efd30 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffffffff8cb67800 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff84ad27e0 RDI: 0000000000000000
RBP: fffffffffffffff4 R08: 0000000000000005 R09: 0000000000000000
R10: 0000000000000000 R11: 000000000008c07c R12: ffff88801fa05000
R13: ffff888073db07e8 R14: ffff888025c25440 R15: 0000000000000000
FS: 0000555555fc4300(0000) GS:ffff8880b9a00000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fc1c0ce06e4 CR3: 00000000715e6000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
dma_buf_release+0x157/0x2d0 drivers/dma-buf/dma-buf.c:78
__dentry_kill+0x42b/0x640 fs/dcache.c:612
dentry_kill fs/dcache.c:733 [inline]
dput+0x806/0xdb0 fs/dcache.c:913
__fput+0x39c/0x9d0 fs/file_table.c:333
task_work_run+0xdd/0x1a0 kernel/task_work.c:177
ptrace_notify+0x114/0x140 kernel/signal.c:2353
ptrace_report_syscall include/linux/ptrace.h:420 [inline]
ptrace_report_syscall_exit include/linux/ptrace.h:482 [inline]
syscall_exit_work kernel/entry/common.c:249 [inline]
syscall_exit_to_user_mode_prepare+0x129/0x280 kernel/entry/common.c:276
__syscall_exit_to_user_mode_work kernel/entry/common.c:281 [inline]
syscall_exit_to_user_mode+0x9/0x50 kernel/entry/common.c:294
do_syscall_64+0x42/0xb0 arch/x86/entry/common.c:86
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7fc1c0c35b6b
Code: 0f 05 48 3d 00 f0 ff ff 77 45 c3 0f 1f 40 00 48 83 ec 18 89 7c 24
0c e8 63 fc ff ff 8b 7c 24 0c 41 89 c0 b8 03 00 00 00 0f 05 <48> 3d 00
f0 ff ff 77 35 44 89 c7 89 44 24 0c e8 a1 fc ff ff 8b 44
RSP: 002b:00007ffd78a06090 EFLAGS: 00000293 ORIG_RAX: 0000000000000003
RAX: 0000000000000000 RBX: 0000000000000007 RCX: 00007fc1c0c35b6b
RDX: 0000000020000280 RSI: 0000000040086200 RDI: 0000000000000006
RBP: 0000000000000007 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000293 R12: 000000000000000c
R13: 0000000000000003 R14: 00007fc1c0cfe4a0 R15: 00007ffd78a06140
</TASK>
Modules linked in:
---[ end trace 0000000000000000 ]---
RIP: 0010:dma_unmap_sgtable include/linux/dma-mapping.h:378 [inline]
RIP: 0010:put_sg_table drivers/dma-buf/udmabuf.c:89 [inline]
RIP: 0010:release_udmabuf+0xcb/0x4f0 drivers/dma-buf/udmabuf.c:114 |
| In the Linux kernel, the following vulnerability has been resolved:
blk-cgroup: hold queue_lock when removing blkg->q_node
When blkg is removed from q->blkg_list from blkg_free_workfn(), queue_lock
has to be held, otherwise, all kinds of bugs(list corruption, hard lockup,
..) can be triggered from blkg_destroy_all(). |
| In the Linux kernel, the following vulnerability has been resolved:
PCI/DOE: Fix destroy_work_on_stack() race
The following debug object splat was observed in testing:
ODEBUG: free active (active state 0) object: 0000000097d23782 object type: work_struct hint: doe_statemachine_work+0x0/0x510
WARNING: CPU: 1 PID: 71 at lib/debugobjects.c:514 debug_print_object+0x7d/0xb0
...
Workqueue: pci 0000:36:00.0 DOE [1 doe_statemachine_work
RIP: 0010:debug_print_object+0x7d/0xb0
...
Call Trace:
? debug_print_object+0x7d/0xb0
? __pfx_doe_statemachine_work+0x10/0x10
debug_object_free.part.0+0x11b/0x150
doe_statemachine_work+0x45e/0x510
process_one_work+0x1d4/0x3c0
This occurs because destroy_work_on_stack() was called after signaling
the completion in the calling thread. This creates a race between
destroy_work_on_stack() and the task->work struct going out of scope in
pci_doe().
Signal the work complete after destroying the work struct. This is safe
because signal_task_complete() is the final thing the work item does and
the workqueue code is careful not to access the work struct after. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: mpi3mr: Fix missing mrioc->evtack_cmds initialization
Commit c1af985d27da ("scsi: mpi3mr: Add Event acknowledgment logic")
introduced an array mrioc->evtack_cmds but initialization of the array
elements was missed. They are just zero cleared. The function
mpi3mr_complete_evt_ack() refers host_tag field of the elements. Due to the
zero value of the host_tag field, the function calls clear_bit() for
mrico->evtack_cmds_bitmap with wrong bit index. This results in memory
access to invalid address and "BUG: KASAN: use-after-free". This BUG was
observed at eHBA-9600 firmware update to version 8.3.1.0. To fix it, add
the missing initialization of mrioc->evtack_cmds. |
| In the Linux kernel, the following vulnerability has been resolved:
net: libwx: fix memory leak in wx_setup_rx_resources
When wx_alloc_page_pool() failed in wx_setup_rx_resources(), it doesn't
release DMA buffer. Add dma_free_coherent() in the error path to release
the DMA buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
amba: bus: fix refcount leak
commit 5de1540b7bc4 ("drivers/amba: create devices from device tree")
increases the refcount of of_node, but not releases it in
amba_device_release, so there is refcount leak. By using of_node_put
to avoid refcount leak. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix registration of 6Ghz-only phy without the full channel range
Because of what seems to be a typo, a 6Ghz-only phy for which the BDF
does not allow the 7115Mhz channel will fail to register:
WARNING: CPU: 2 PID: 106 at net/wireless/core.c:907 wiphy_register+0x914/0x954
Modules linked in: ath11k_pci sbsa_gwdt
CPU: 2 PID: 106 Comm: kworker/u8:5 Not tainted 6.3.0-rc7-next-20230418-00549-g1e096a17625a-dirty #9
Hardware name: Freebox V7R Board (DT)
Workqueue: ath11k_qmi_driver_event ath11k_qmi_driver_event_work
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : wiphy_register+0x914/0x954
lr : ieee80211_register_hw+0x67c/0xc10
sp : ffffff800b123aa0
x29: ffffff800b123aa0 x28: 0000000000000000 x27: 0000000000000000
x26: 0000000000000000 x25: 0000000000000006 x24: ffffffc008d51418
x23: ffffffc008cb0838 x22: ffffff80176c2460 x21: 0000000000000168
x20: ffffff80176c0000 x19: ffffff80176c03e0 x18: 0000000000000014
x17: 00000000cbef338c x16: 00000000d2a26f21 x15: 00000000ad6bb85f
x14: 0000000000000020 x13: 0000000000000020 x12: 00000000ffffffbd
x11: 0000000000000208 x10: 00000000fffffdf7 x9 : ffffffc009394718
x8 : ffffff80176c0528 x7 : 000000007fffffff x6 : 0000000000000006
x5 : 0000000000000005 x4 : ffffff800b304284 x3 : ffffff800b304284
x2 : ffffff800b304d98 x1 : 0000000000000000 x0 : 0000000000000000
Call trace:
wiphy_register+0x914/0x954
ieee80211_register_hw+0x67c/0xc10
ath11k_mac_register+0x7c4/0xe10
ath11k_core_qmi_firmware_ready+0x1f4/0x570
ath11k_qmi_driver_event_work+0x198/0x590
process_one_work+0x1b8/0x328
worker_thread+0x6c/0x414
kthread+0x100/0x104
ret_from_fork+0x10/0x20
---[ end trace 0000000000000000 ]---
ath11k_pci 0002:01:00.0: ieee80211 registration failed: -22
ath11k_pci 0002:01:00.0: failed register the radio with mac80211: -22
ath11k_pci 0002:01:00.0: failed to create pdev core: -22 |
| In the Linux kernel, the following vulnerability has been resolved:
blk-mq: fix tags leak when shrink nr_hw_queues
Although we don't need to realloc set->tags[] when shrink nr_hw_queues,
we need to free them. Or these tags will be leaked.
How to reproduce:
1. mount -t configfs configfs /mnt
2. modprobe null_blk nr_devices=0 submit_queues=8
3. mkdir /mnt/nullb/nullb0
4. echo 1 > /mnt/nullb/nullb0/power
5. echo 4 > /mnt/nullb/nullb0/submit_queues
6. rmdir /mnt/nullb/nullb0
In step 4, will alloc 9 tags (8 submit queues and 1 poll queue), then
in step 5, new_nr_hw_queues = 5 (4 submit queues and 1 poll queue).
At last in step 6, only these 5 tags are freed, the other 4 tags leaked. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ipa: only reset hashed tables when supported
Last year, the code that manages GSI channel transactions switched
from using spinlock-protected linked lists to using indexes into the
ring buffer used for a channel. Recently, Google reported seeing
transaction reference count underflows occasionally during shutdown.
Doug Anderson found a way to reproduce the issue reliably, and
bisected the issue to the commit that eliminated the linked lists
and the lock. The root cause was ultimately determined to be
related to unused transactions being committed as part of the modem
shutdown cleanup activity. Unused transactions are not normally
expected (except in error cases).
The modem uses some ranges of IPA-resident memory, and whenever it
shuts down we zero those ranges. In ipa_filter_reset_table() a
transaction is allocated to zero modem filter table entries. If
hashing is not supported, hashed table memory should not be zeroed.
But currently nothing prevents that, and the result is an unused
transaction. Something similar occurs when we zero routing table
entries for the modem.
By preventing any attempt to clear hashed tables when hashing is not
supported, the reference count underflow is avoided in this case.
Note that there likely remains an issue with properly freeing unused
transactions (if they occur due to errors). This patch addresses
only the underflows that Google originally reported. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: 8250: Fix oops for port->pm on uart_change_pm()
Unloading a hardware specific 8250 driver can produce error "Unable to
handle kernel paging request at virtual address" about ten seconds after
unloading the driver. This happens on uart_hangup() calling
uart_change_pm().
Turns out commit 04e82793f068 ("serial: 8250: Reinit port->pm on port
specific driver unbind") was only a partial fix. If the hardware specific
driver has initialized port->pm function, we need to clear port->pm too.
Just reinitializing port->ops does not do this. Otherwise serial8250_pm()
will call port->pm() instead of serial8250_do_pm(). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix NULL dereference in ath11k_qmi_m3_load()
If ab->fw.m3_data points to data, then fw pointer remains null.
Further, if m3_mem is not allocated, then fw is dereferenced to be
passed to ath11k_err function.
Replace fw->size by m3_len.
Found by Linux Verification Center (linuxtesting.org) with SVACE. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: TC, Fix using eswitch mapping in nic mode
Cited patch is using the eswitch object mapping pool while
in nic mode where it isn't initialized. This results in the
trace below [0].
Fix that by using either nic or eswitch object mapping pool
depending if eswitch is enabled or not.
[0]:
[ 826.446057] ==================================================================
[ 826.446729] BUG: KASAN: slab-use-after-free in mlx5_add_flow_rules+0x30/0x490 [mlx5_core]
[ 826.447515] Read of size 8 at addr ffff888194485830 by task tc/6233
[ 826.448243] CPU: 16 PID: 6233 Comm: tc Tainted: G W 6.3.0-rc6+ #1
[ 826.448890] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[ 826.449785] Call Trace:
[ 826.450052] <TASK>
[ 826.450302] dump_stack_lvl+0x33/0x50
[ 826.450650] print_report+0xc2/0x610
[ 826.450998] ? __virt_addr_valid+0xb1/0x130
[ 826.451385] ? mlx5_add_flow_rules+0x30/0x490 [mlx5_core]
[ 826.451935] kasan_report+0xae/0xe0
[ 826.452276] ? mlx5_add_flow_rules+0x30/0x490 [mlx5_core]
[ 826.452829] mlx5_add_flow_rules+0x30/0x490 [mlx5_core]
[ 826.453368] ? __kmalloc_node+0x5a/0x120
[ 826.453733] esw_add_restore_rule+0x20f/0x270 [mlx5_core]
[ 826.454288] ? mlx5_eswitch_add_send_to_vport_meta_rule+0x260/0x260 [mlx5_core]
[ 826.455011] ? mutex_unlock+0x80/0xd0
[ 826.455361] ? __mutex_unlock_slowpath.constprop.0+0x210/0x210
[ 826.455862] ? mapping_add+0x2cb/0x440 [mlx5_core]
[ 826.456425] mlx5e_tc_action_miss_mapping_get+0x139/0x180 [mlx5_core]
[ 826.457058] ? mlx5e_tc_update_skb_nic+0xb0/0xb0 [mlx5_core]
[ 826.457636] ? __kasan_kmalloc+0x77/0x90
[ 826.458000] ? __kmalloc+0x57/0x120
[ 826.458336] mlx5_tc_ct_flow_offload+0x325/0xe40 [mlx5_core]
[ 826.458916] ? ct_kernel_enter.constprop.0+0x48/0xa0
[ 826.459360] ? mlx5_tc_ct_parse_action+0xf0/0xf0 [mlx5_core]
[ 826.459933] ? mlx5e_mod_hdr_attach+0x491/0x520 [mlx5_core]
[ 826.460507] ? mlx5e_mod_hdr_get+0x12/0x20 [mlx5_core]
[ 826.461046] ? mlx5e_tc_attach_mod_hdr+0x154/0x170 [mlx5_core]
[ 826.461635] mlx5e_configure_flower+0x969/0x2110 [mlx5_core]
[ 826.462217] ? _raw_spin_lock_bh+0x85/0xe0
[ 826.462597] ? __mlx5e_add_fdb_flow+0x750/0x750 [mlx5_core]
[ 826.463163] ? kasan_save_stack+0x2e/0x40
[ 826.463534] ? down_read+0x115/0x1b0
[ 826.463878] ? down_write_killable+0x110/0x110
[ 826.464288] ? tc_setup_action.part.0+0x9f/0x3b0
[ 826.464701] ? mlx5e_is_uplink_rep+0x4c/0x90 [mlx5_core]
[ 826.465253] ? mlx5e_tc_reoffload_flows_work+0x130/0x130 [mlx5_core]
[ 826.465878] tc_setup_cb_add+0x112/0x250
[ 826.466247] fl_hw_replace_filter+0x230/0x310 [cls_flower]
[ 826.466724] ? fl_hw_destroy_filter+0x1a0/0x1a0 [cls_flower]
[ 826.467212] fl_change+0x14e1/0x2030 [cls_flower]
[ 826.467636] ? sock_def_readable+0x89/0x120
[ 826.468019] ? fl_tmplt_create+0x2d0/0x2d0 [cls_flower]
[ 826.468509] ? kasan_unpoison+0x23/0x50
[ 826.468873] ? get_random_u16+0x180/0x180
[ 826.469244] ? __radix_tree_lookup+0x2b/0x130
[ 826.469640] ? fl_get+0x7b/0x140 [cls_flower]
[ 826.470042] ? fl_mask_put+0x200/0x200 [cls_flower]
[ 826.470478] ? __mutex_unlock_slowpath.constprop.0+0x210/0x210
[ 826.470973] ? fl_tmplt_create+0x2d0/0x2d0 [cls_flower]
[ 826.471427] tc_new_tfilter+0x644/0x1050
[ 826.471795] ? tc_get_tfilter+0x860/0x860
[ 826.472170] ? __thaw_task+0x130/0x130
[ 826.472525] ? arch_stack_walk+0x98/0xf0
[ 826.472892] ? cap_capable+0x9f/0xd0
[ 826.473235] ? security_capable+0x47/0x60
[ 826.473608] rtnetlink_rcv_msg+0x1d5/0x550
[ 826.473985] ? rtnl_calcit.isra.0+0x1f0/0x1f0
[ 826.474383] ? __stack_depot_save+0x35/0x4c0
[ 826.474779] ? kasan_save_stack+0x2e/0x40
[ 826.475149] ? kasan_save_stack+0x1e/0x40
[ 826.475518] ? __kasan_record_aux_stack+0x9f/0xb0
[ 826.475939] ? task_work_add+0x77/0x1c0
[ 826.476305] netlink_rcv_skb+0xe0/0x210
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
USB: sisusbvga: Add endpoint checks
The syzbot fuzzer was able to provoke a WARNING from the sisusbvga driver:
------------[ cut here ]------------
usb 1-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 1 PID: 26 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
Modules linked in:
CPU: 1 PID: 26 Comm: kworker/1:1 Not tainted 6.2.0-rc5-syzkaller-00199-g5af6ce704936 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/12/2023
Workqueue: usb_hub_wq hub_event
RIP: 0010:usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
Code: 7c 24 18 e8 6c 50 80 fb 48 8b 7c 24 18 e8 62 1a 01 ff 41 89 d8 44 89 e1 4c 89 ea 48 89 c6 48 c7 c7 60 b1 fa 8a e8 84 b0 be 03 <0f> 0b e9 58 f8 ff ff e8 3e 50 80 fb 48 81 c5 c0 05 00 00 e9 84 f7
RSP: 0018:ffffc90000a1ed18 EFLAGS: 00010282
RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000000
RDX: ffff888012783a80 RSI: ffffffff816680ec RDI: fffff52000143d95
RBP: ffff888079020000 R08: 0000000000000005 R09: 0000000000000000
R10: 0000000080000000 R11: 0000000000000000 R12: 0000000000000003
R13: ffff888017d33370 R14: 0000000000000003 R15: ffff888021213600
FS: 0000000000000000(0000) GS:ffff8880b9900000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00005592753a60b0 CR3: 0000000022899000 CR4: 00000000003506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
sisusb_bulkout_msg drivers/usb/misc/sisusbvga/sisusbvga.c:224 [inline]
sisusb_send_bulk_msg.constprop.0+0x904/0x1230 drivers/usb/misc/sisusbvga/sisusbvga.c:379
sisusb_send_bridge_packet drivers/usb/misc/sisusbvga/sisusbvga.c:567 [inline]
sisusb_do_init_gfxdevice drivers/usb/misc/sisusbvga/sisusbvga.c:2077 [inline]
sisusb_init_gfxdevice+0x87b/0x4000 drivers/usb/misc/sisusbvga/sisusbvga.c:2177
sisusb_probe+0x9cd/0xbe2 drivers/usb/misc/sisusbvga/sisusbvga.c:2869
...
The problem was caused by the fact that the driver does not check
whether the endpoints it uses are actually present and have the
appropriate types. This can be fixed by adding a simple check of
the endpoints. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix slab-out-of-bounds in init_smb2_rsp_hdr
When smb1 mount fails, KASAN detect slab-out-of-bounds in
init_smb2_rsp_hdr like the following one.
For smb1 negotiate(56bytes) , init_smb2_rsp_hdr() for smb2 is called.
The issue occurs while handling smb1 negotiate as smb2 server operations.
Add smb server operations for smb1 (get_cmd_val, init_rsp_hdr,
allocate_rsp_buf, check_user_session) to handle smb1 negotiate so that
smb2 server operation does not handle it.
[ 411.400423] CIFS: VFS: Use of the less secure dialect vers=1.0 is
not recommended unless required for access to very old servers
[ 411.400452] CIFS: Attempting to mount \\192.168.45.139\homes
[ 411.479312] ksmbd: init_smb2_rsp_hdr : 492
[ 411.479323] ==================================================================
[ 411.479327] BUG: KASAN: slab-out-of-bounds in
init_smb2_rsp_hdr+0x1e2/0x1f4 [ksmbd]
[ 411.479369] Read of size 16 at addr ffff888488ed0734 by task kworker/14:1/199
[ 411.479379] CPU: 14 PID: 199 Comm: kworker/14:1 Tainted: G
OE 6.1.21 #3
[ 411.479386] Hardware name: ASUSTeK COMPUTER INC. Z10PA-D8
Series/Z10PA-D8 Series, BIOS 3801 08/23/2019
[ 411.479390] Workqueue: ksmbd-io handle_ksmbd_work [ksmbd]
[ 411.479425] Call Trace:
[ 411.479428] <TASK>
[ 411.479432] dump_stack_lvl+0x49/0x63
[ 411.479444] print_report+0x171/0x4a8
[ 411.479452] ? kasan_complete_mode_report_info+0x3c/0x200
[ 411.479463] ? init_smb2_rsp_hdr+0x1e2/0x1f4 [ksmbd]
[ 411.479497] kasan_report+0xb4/0x130
[ 411.479503] ? init_smb2_rsp_hdr+0x1e2/0x1f4 [ksmbd]
[ 411.479537] kasan_check_range+0x149/0x1e0
[ 411.479543] memcpy+0x24/0x70
[ 411.479550] init_smb2_rsp_hdr+0x1e2/0x1f4 [ksmbd]
[ 411.479585] handle_ksmbd_work+0x109/0x760 [ksmbd]
[ 411.479616] ? _raw_spin_unlock_irqrestore+0x50/0x50
[ 411.479624] ? smb3_encrypt_resp+0x340/0x340 [ksmbd]
[ 411.479656] process_one_work+0x49c/0x790
[ 411.479667] worker_thread+0x2b1/0x6e0
[ 411.479674] ? process_one_work+0x790/0x790
[ 411.479680] kthread+0x177/0x1b0
[ 411.479686] ? kthread_complete_and_exit+0x30/0x30
[ 411.479692] ret_from_fork+0x22/0x30
[ 411.479702] </TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
drm/i915: fix race condition UAF in i915_perf_add_config_ioctl
Userspace can guess the id value and try to race oa_config object creation
with config remove, resulting in a use-after-free if we dereference the
object after unlocking the metrics_lock. For that reason, unlocking the
metrics_lock must be done after we are done dereferencing the object.
[tursulin: Manually added stable tag.]
(cherry picked from commit 49f6f6483b652108bcb73accd0204a464b922395) |
| In the Linux kernel, the following vulnerability has been resolved:
blk-mq: fix blk_mq_tags double free while nr_requests grown
In the case user trigger tags grow by queue sysfs attribute nr_requests,
hctx->sched_tags will be freed directly and replaced with a new
allocated tags, see blk_mq_tag_update_depth().
The problem is that hctx->sched_tags is from elevator->et->tags, while
et->tags is still the freed tags, hence later elevator exit will try to
free the tags again, causing kernel panic.
Fix this problem by replacing et->tags with new allocated tags as well.
Noted there are still some long term problems that will require some
refactor to be fixed thoroughly[1].
[1] https://lore.kernel.org/all/20250815080216.410665-1-yukuai1@huaweicloud.com/ |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: always release netdev hooks from notifier
This reverts "netfilter: nf_tables: skip netdev events generated on netns removal".
The problem is that when a veth device is released, the veth release
callback will also queue the peer netns device for removal.
Its possible that the peer netns is also slated for removal. In this
case, the device memory is already released before the pre_exit hook of
the peer netns runs:
BUG: KASAN: slab-use-after-free in nf_hook_entry_head+0x1b8/0x1d0
Read of size 8 at addr ffff88812c0124f0 by task kworker/u8:1/45
Workqueue: netns cleanup_net
Call Trace:
nf_hook_entry_head+0x1b8/0x1d0
__nf_unregister_net_hook+0x76/0x510
nft_netdev_unregister_hooks+0xa0/0x220
__nft_release_hook+0x184/0x490
nf_tables_pre_exit_net+0x12f/0x1b0
..
Order is:
1. First netns is released, veth_dellink() queues peer netns device
for removal
2. peer netns is queued for removal
3. peer netns device is released, unreg event is triggered
4. unreg event is ignored because netns is going down
5. pre_exit hook calls nft_netdev_unregister_hooks but device memory
might be free'd already. |
