| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| The Zephyr PL011 UART driver (drivers/serial/uart_pl011.c) contains an unbounded software loop in pl011_irq_tx_enable() that repeatedly invokes the interrupt-driven application callback while the TX interrupt mask bit (PL011_IMSC_TXIM) is set, to work around the controller's level-transition TX-interrupt behavior.
When CTS hardware flow control is enabled (devicetree hw-flow-control or runtime UART_CFG_FLOW_CTRL_RTS_CTS) and the wired serial peer de-asserts CTS, the controller stops draining the TX FIFO; pl011_fifo_fill() then returns 0 on every call while the application still has pending data and therefore never disables the TX interrupt. The loop condition never clears, so the thread that called uart_irq_tx_enable() (e.g. h4_send() in the Bluetooth HCI H4 driver) spins indefinitely, hanging the executing context and stalling the transport — a denial of service (CWE-835).
An attacker controlling the device attached to the UART's CTS line can trigger the hang by withholding CTS during transmission. Because that peer is the device wired to the UART — which may be a removable or external module (e.g. an off-board Bluetooth controller on the HCI H4 link) rather than a permanently-bonded on-PCB part — the attack vector is scored Adjacent (AV:A) rather than Physical; the security subcommittee should confirm the vector against the specific deployment. Impact is availability only; there is no memory-safety, confidentiality, or integrity consequence.
The vulnerable loop was introduced in commit b783bc8448ef (Feb 2025) and shipped in releases v4.1.0 through v4.4.0. The fix breaks out of the loop when CTS is blocking and arms the CTS modem-status interrupt to resume transmission when CTS re-asserts. |
| Zephyr's Bluetooth Classic Hands-Free Profile (HFP) Hands-Free role parser (subsys/bluetooth/host/classic/hfp_hf.c) contains an out-of-bounds write. During Service Level Connection setup the HF sends AT+CIND=? and parses the AG's +CIND: response in cind_handle(), which assigns a per-entry counter index and calls cind_handle_values() for each list element. cind_handle_values() then wrote hf->ind_table[index] = i without verifying that index is within the 20-element int8_t ind_table[] array of struct bt_hfp_hf. Because the parser places no cap on the number of +CIND: list entries, a remote Attendant Gateway (a malicious, compromised, or spoofed peer the device connects to over Bluetooth) can send a response with more than 20 recognized indicator entries and drive index arbitrarily large, writing a small attacker-positioned value past the array into adjacent struct fields (feature masks, SDP/version state, the calls[] array, work/atomic bookkeeping) and potentially beyond the static connection pool slot. This yields memory corruption and at least denial of service of the Bluetooth host, triggered by a single malformed AT response with no user interaction. The sibling consumer ag_indicator_handle_values() already performed the equivalent bounds check; this commit adds the same index >= ARRAY_SIZE(hf->ind_table) guard to close the gap. Affects builds with CONFIG_BT_HFP_HF enabled; introduced with the original HFP HF CIND parser (~v1.7) and present through v4.4.0. |
| Zephyr's IPv6 Neighbor Discovery send paths (net_ipv6_send_na, net_ipv6_send_ns, net_ipv6_send_rs in subsys/net/ip/ipv6_nbr.c) updated the per-interface ICMP-sent statistics by calling net_pkt_iface(pkt) after net_send_data(pkt) had already returned successfully. On the success path the network stack owns and releases the packet's reference (the L2/driver send unrefs it, e.g. ethernet_send -> net_pkt_unref), so for a freshly allocated packet with refcount 1 the net_pkt slab block can be freed before the statistics line runs (synchronously when no TX queue thread is configured, or via a concurrent TX thread otherwise).
The subsequent net_pkt_iface(pkt) reads pkt->iface from the freed slab block, and with CONFIG_NET_STATISTICS_PER_INTERFACE enabled that loaded pointer is dereferenced to increment iface->stats.icmp.sent, a use-after-free (CWE-416). If the slab block was reallocated in the meantime the read/increment targets unrelated or attacker-influenced memory, yielding corrupted statistics, a fault/crash (denial of service), or potential limited memory corruption.
The vulnerable Neighbor Advertisement path is reachable by any unauthenticated on-link node simply by sending ICMPv6 Neighbor Solicitations to a Zephyr node with native IPv6 enabled (handle_ns_input -> net_ipv6_send_na).
Affected from v3.3.0 through v4.4.0; the fix uses the already-available iface argument instead of touching the sent packet. Configurations without per-interface statistics dereference only a global counter and are not affected by the memory-safety aspect. |
| In Zephyr's native IPv4 stack, icmpv4_handle_echo_request() in subsys/net/ip/icmpv4.c builds an echo-reply packet (reply), hands it to net_try_send_data(), and then, on success, calls net_stats_update_icmp_sent(net_pkt_iface(reply)). net_try_send_data() transfers ownership of reply to the TX path (net_if_try_queue_tx -> net_if_tx -> L2/driver send, or the asynchronous net_if_tx_thread), which can unref it to refcount 0 and return the struct net_pkt to its slab (net_pkt_unref -> k_mem_slab_free) before the stats line runs. net_core.c documents this exact contract ('the pkt might contain garbage already ... do not use pkt after that call').
The post-send net_pkt_iface(reply) therefore reads reply->iface out of a freed (and possibly already reallocated) net_pkt, a use-after-free read; with CONFIG_NET_STATISTICS_PER_INTERFACE the stats macro additionally increments a counter through that value, i.e. a dereference/write through a stale or recycled-slot pointer.
The path is reached unauthenticated by any remote host that pings the device (net_icmpv4_input -> net_icmp_call_ipv4_handlers -> icmpv4_handle_echo_request) and is gated on CONFIG_NET_STATISTICS_ICMP. Impact is a probabilistic read of recycled packet memory plus a possible wild-pointer write under a timing race, leading most likely to corrupted interface statistics or a remotely triggerable crash (DoS).
The defect was introduced in 2019 (v1.14) and is present through v4.4.0. The companion change in net_icmpv4_send_error() is not a use-after-free because it reads net_pkt_iface(orig), the caller-owned received packet, which stays alive across the send. The fix caches the interface pointer from the live received packet before sending and uses it for the post-send stats updates. |
| On Xtensa targets with CONFIG_USERSPACE and CONFIG_XTENSA_MMU, the page-table code (arch/xtensa/core/ptables.c) maintains a global list, xtensa_domain_list, of active memory domains using a list node embedded inside the caller-owned struct k_mem_domain. When a domain is destroyed via k_mem_domain_deinit() -> arch_mem_domain_deinit(), the page tables are torn down and domain->arch.ptables is set to NULL, but the domain's node was not removed from xtensa_domain_list. The freed/deinitialized domain therefore remained linked into the global list as a dangling pointer into caller-owned storage that may then be freed or reused.
Any subsequent arch_mem_map()/arch_mem_unmap() operation (widely invoked by kernel memory-mapping and demand-paging code) traverses the stale node and dereferences domain->ptables: at minimum a NULL pointer dereference causing a fatal MMU exception (denial of service), and if the k_mem_domain storage has been freed or reused, a use-after-free in which a stale/controlled ptables value is dereferenced and written through during the page-table walk (l2_page_table_map writes l1_table[...] and l2_table[...], and xtensa_mmu_compute_domain_regs writes into the domain struct and the L1 table), yielding page-table memory corruption that can undermine userspace isolation.
The vulnerable path is reachable only from privileged kernel/supervisor code (k_mem_domain_deinit is not a syscall), not directly from unprivileged user threads or remotely. Affected: Zephyr v4.4.0 (the Xtensa memory-domain de-initialization feature was introduced in commit 3032b58f52d and first shipped in v4.4.0); fixed on main by adding sys_slist_find_and_remove() in arch_mem_domain_deinit(). The Xtensa MPU path is unaffected. |
| subsys/net/ip/ipv6_mld.c:mld_send() read the packet interface via net_pkt_iface(pkt) after net_send_data(pkt) returned successfully. Per the network stack's ownership contract (include/zephyr/net/net_core.h, and the explicit warning in subsys/net/ip/net_core.c:453-460 'do not use pkt after that call'), a successful send transfers ownership of the net_pkt and the L2 driver frees it (e.g. ethernet_send() unrefs the packet on success, subsys/net/l2/ethernet/ethernet.c:790), returning it to its k_mem_slab.
The subsequent net_pkt_iface(pkt) is therefore a read of a freed object; the recovered interface pointer is then dereferenced and incremented by the per-interface statistics path (net_stats.h UPDATE_STAT/SET_STAT) when CONFIG_NET_STATISTICS_PER_INTERFACE is enabled. If the freed slot is concurrently reallocated, pkt->iface may read back as NULL (NULL-pointer dereference / crash) or as a stale/garbage pointer (stray increment write / memory corruption).
The path is reachable remotely on the local link without authentication: handle_mld_query() (registered for NET_ICMPV6_MLD_QUERY) responds to a valid MLDv2 General Query (unspecified multicast address, hop limit 1) by calling send_mld_report() -> mld_send().
The result is a remotely triggerable denial of service of the networking stack, with a narrow possibility of memory corruption. The fix caches the interface in a local before sending and no longer touches the packet after net_send_data(). The IPv4/IGMP sibling (igmp_send) already used the corrected pattern. |
| subsys/net/ip/icmpv6.c reads the network interface from a net_pkt after that packet has been handed to net_try_send_data(). In icmpv6_handle_echo_request() and net_icmpv6_send_error(), the post-send statistics update calls net_pkt_iface(reply)/net_pkt_iface(pkt) on the just-sent packet.
The send path (net_try_send_data -> net_if_tx) unreferences and may free the packet back to its memory slab before returning — synchronously in the RX thread when no TX queue is configured (CONFIG_NET_TC_TX_COUNT == 0), and asynchronously the driver/L2 may already have freed it otherwise. net_pkt_iface() therefore dereferences a freed (and possibly reused) net_pkt; with CONFIG_NET_STATISTICS_PER_INTERFACE the stale iface pointer is further dereferenced and written through (iface->stats.icmp.sent++), turning the use-after-free read into a write through an attacker-influenceable pointer.
The core stack already documents this hazard in net_core.c ("do not use pkt after that call") and caches iface before sending; the ICMPv6 callers did not.
An unauthenticated remote attacker triggers the flaw simply by sending an ICMPv6 Echo Request (ping) or an IPv6 packet that elicits an ICMPv6 error (unknown next header, fragment reassembly timeout, destination unreachable), leading to denial of service via crash and potential memory corruption. Affected: Zephyr networking with CONFIG_NET_NATIVE_IPV6, roughly v4.2.0 through v4.4.0.
The fix caches the interface pointer before sending and uses it for all statistics updates; the sibling commit 86e21665d46 fixes the identical bug in ICMPv4. |
| In Zephyr's IPv4 IGMP implementation, igmp_send() in subsys/net/ip/igmp.c read the network interface back out of the packet via net_pkt_iface(pkt) after the packet had been handed to net_send_data(). On the successful-send path the packet's last reference may already have been released by the L2 driver or by the network stack's TX handling (synchronously in the default NET_TC_TX_COUNT=0 immediate-transmit configuration), returning the net_pkt slab block to its free list. The subsequent net_pkt_iface(pkt) dereferences the freed packet, a use-after-free read; with CONFIG_NET_STATISTICS_PER_INTERFACE the resulting dangling interface pointer is further dereferenced for a statistics-counter write.
The IGMP send path is reachable without authentication from inbound IPv4 IGMP membership queries addressed to 224.0.0.1 (net_ipv4_igmp_input -> send_igmp_report/send_igmp_v3_report -> igmp_send), as well as from local multicast join/leave/rejoin operations.
Realistic impact is undefined behavior and potential denial of service (sporadic crash or stats corruption); a controllable write requires the asynchronous TX path plus a concurrent slab reuse.
The flaw was introduced with IGMPv2 support and affects releases from v2.6.0 through v4.4.0. The fix caches the interface pointer before sending. Note the analogous IPv6 MLD path (mld_send in subsys/net/ip/ipv6_mld.c) retains the same unfixed pattern. |
| Zephyr's native TCP stack iterates the global connection list in net_tcp_foreach() (subsys/net/ip/tcp.c) using the SYS_SLIST_FOR_EACH_CONTAINER_SAFE macro, which caches a pointer to the next list node. Prior to this fix the function released tcp_lock while invoking the per-connection callback and re-acquired it afterwards.
During that window a concurrent tcp_conn_release(), running on the dedicated TCP work-queue thread when a connection's reference count drops to zero (e.g. a remote peer closing or resetting the connection), can remove and k_mem_slab_free() the cached next connection. When the iterator advances it dereferences the freed (and possibly reallocated) slab memory — a use-after-free that can crash the system (denial of service) and, if the slot has been reused, cause the callback to operate on an attacker-influenced object (potential information disclosure or further fault).
net_tcp_foreach() is reached in production via the net conn network shell command and via net_tcp_close_all_for_iface() on interface-down; the freeing side is driven by ordinary TCP traffic.
The fix moves the connection/context teardown in tcp_conn_release() inside the tcp_lock critical section and keeps tcp_lock held across the callback in net_tcp_foreach(). The defect was introduced with the modern (TCP2) stack in 2020 and affects releases up to and including v4.4.0. |
| On Xtensa SoCs built with CONFIG_XTENSA_MPU and CONFIG_USERSPACE, arch_buffer_validate() in arch/xtensa/core/mpu.c — the architecture hook that verifies a user-mode-supplied buffer is accessible to the calling user thread with the requested permission — defaulted its return value to 0 (access permitted) and only set a denial result inside its per-MPU-region probe loop. When the rounded extent of the buffer wraps the 32-bit address space (size + alignment offset near SIZE_MAX, or ROUND_UP(size + offset) overflowing to 0), the loop executes zero iterations and the function returns 0 = permitted without probing any MPU region.
The syscall-layer pre-checks (K_SYSCALL_MEMORY_SIZE_CHECK / Z_DETECT_POINTER_OVERFLOW) only catch a raw addr+size wrap and do not cover the ROUND_UP-induced wrap, and the string path (arch_user_string_nlen -> arch_buffer_validate) has no syscall-layer guard at all.
An unprivileged user-mode thread can therefore pass a crafted (addr, size) to any syscall that validates user buffers via k_usermode_from_copy/to_copy or k_usermode_string_copy and have validation succeed for memory it must not access; the kernel then reads from (disclosure) or, with write=1, writes to (corruption) attacker-chosen kernel or other-partition memory on the thread's behalf, enabling information disclosure, memory corruption, privilege escalation, and denial of service.
Affected from v3.7.0 (when Xtensa MPU userspace support was added) through v4.4.0. The fix changes the default to -EINVAL (deny by default), adds an explicit size_add_overflow check, and sets the success value only after the full range has been validated. |
| The CONFIG_USERSPACE verification handler for the k_thread_name_copy() system call (z_vrfy_k_thread_name_copy() in kernel/thread.c) calls k_object_find() on the caller-supplied thread pointer and then dereferences the returned struct k_object without checking it for NULL. k_object_find() returns NULL whenever the supplied pointer is not a registered (static or dynamic) kernel object.
The pre-fix guard tested thread == NULL instead of ko == NULL, so an unprivileged user-mode thread that invokes k_thread_name_copy() with any non-NULL but unregistered pointer (e.g. an arbitrary address) passes the NULL test, after which the verifier reads ko->type through a NULL pointer.
Because the syscall verifier runs in supervisor mode, this NULL dereference is a kernel-mode fault that halts or reboots the system, allowing untrusted user code to crash the kernel across the userspace security boundary (denial of service). The marshaller passes the thread argument to the verifier without any prior K_SYSCALL_OBJ validation, so the bad pointer reaches the defect directly.
The flaw affects builds with CONFIG_USERSPACE and CONFIG_THREAD_NAME enabled and has been present since the special-case lookup was introduced around v2.0.0; it is present in v4.4.0 and earlier. The fix changes the guard to check the k_object_find() return value (ko == NULL) before dereferencing it. |
| In Zephyr's kernel pipe implementation, the userspace syscall verifier z_vrfy_k_pipe_init() in kernel/pipe.c used K_SYSCALL_OBJ() (which requires the kernel object to already be initialized) instead of K_SYSCALL_OBJ_NEVER_INIT() (which rejects an already-initialized object). As a result, on CONFIG_USERSPACE builds an unprivileged user thread that has been granted access to a k_pipe object can invoke the k_pipe_init syscall to re-initialize a pipe that is already in use.
z_impl_k_pipe_init() unconditionally resets the ring buffer, sets pipe->waiting to 0, and re-initializes both wait queues (z_waitq_init on pipe->data and pipe->space) without waking or accounting for threads currently blocked on the pipe. Any thread already pended in k_pipe_read()/k_pipe_write() is left orphaned: still marked pending with pended_on pointing at the cleared wait queue and with stale qnode_dlist links into the (now re-initialized) embedded list head.
When such an orphaned waiter is later timed out or woken, the scheduler calls sys_dlist_remove() on its stale node, writing through dangling prev/next pointers into kernel wait-queue/scheduler structures, causing list corruption (an attacker-driven invalid kernel write), lost wakeups, indefinitely blocked threads, and silent data loss. The flaw lets a deprivileged user thread corrupt the state of a kernel object shared with other threads/partitions.
The fix switches the verifier to K_SYSCALL_OBJ_NEVER_INIT(), matching the existing k_msgq_init verifier, so a user thread can no longer re-initialize a live pipe. The vulnerable code shipped in v4.1.0 and remained through v4.4.0. |
| subsys/net/lib/lwm2m/lwm2m_pull_context.c copied the firmware-update Package URI into a fixed static buffer (context.uri, size CONFIG_LWM2M_SWMGMT_PACKAGE_URI_LEN, default 128) with memcpy(context.uri, uri, LWM2M_PACKAGE_URI_LEN), copying exactly the destination size with no length validation. The Firmware-Update object stores the server-supplied Package URI (/5/0/1) in a 255-byte buffer, so a LwM2M management server (or an on-path attacker on a session lacking strong DTLS) can WRITE a URI of 128-254 characters; only the first 128 bytes are then copied into context.uri with no NUL terminator. That buffer is subsequently consumed as a C string by http_parser_parse_url(context.uri, strlen(context.uri), ...), strlen-based CoAP URI-path/PROXY-URI option appends, and lwm2m_parse_peerinfo(), causing an out-of-bounds read of adjacent static memory. The over-read bytes are appended to outbound CoAP requests (information disclosure of adjacent device memory to the server/proxy) and can crash the device (denial of service). The vulnerable copy was introduced by the pull-context refactor (first released in v3.0.0) and is present through v4.4.0; the default-on CONFIG_LWM2M_FIRMWARE_UPDATE_PULL_SUPPORT path is affected. The fix adds a strlen(uri) >= sizeof(context.uri) check returning -ENOMEM and switches to strcpy(), guaranteeing a bounded, NUL-terminated buffer. |
| Zephyr's dynamic kernel-object tracking (kernel/userspace/userspace.c, formerly kernel/userspace.c) maintains a doubly-linked list (obj_list) of dynamically allocated kernel objects. Iteration over this list in k_object_wordlist_foreach() was performed under lists_lock using the SAFE iterator (which caches the next node), but list removal and freeing of nodes was performed under different, disjoint spinlocks: objfree_lock in k_object_free() and obj_lock in unref_check(). On an SMP system, while one CPU iterated obj_list under lists_lock, another CPU could unlink and k_free() the dyn_obj node that the iterator had cached as its next pointer, causing the iterator to dereference freed kernel memory (use-after-free / dangling list traversal). All of the racing operations are reachable from unprivileged user-mode threads via system calls: k_object_alloc/k_object_alloc_size and k_object_release drive removals through unref_check() (under obj_lock), while k_thread_abort and thread creation drive the iteration through k_thread_perms_all_clear()/k_thread_perms_inherit() (under lists_lock). A deprivileged user thread on a CONFIG_SMP + CONFIG_USERSPACE build can therefore corrupt the kernel's object-tracking structures across the userspace security boundary, yielding kernel memory corruption (potential privilege escalation) or a kernel crash (denial of service). The fix removes objfree_lock and serializes every obj_list modification under lists_lock, including holding it across find+remove in k_object_free() and around unref_check() in k_thread_perms_clear(). Affects CONFIG_SMP+CONFIG_USERSPACE+CONFIG_DYNAMIC_OBJECTS configurations; the defect dates to the 2019 spinlockification (commit 8a3d57b6cc6, first released in v1.14.0) and shipped through v4.4.0. |
| In Zephyr's WireGuard subsystem (subsys/net/lib/wireguard), wg_process_data_message() in wg_crypto.c linearizes an inbound transport-data payload into a fixed pool buffer of CONFIG_WIREGUARD_BUF_LEN bytes before decryption. The call net_buf_linearize(buf->data, data_len, pkt->buffer, ..., data_len) passed the attacker-derived data_len as both the destination capacity and the copy length, defeating the function's internal len = min(len, dst_len) bound. data_len is derived from the received UDP datagram length and is only lower-bounded by wg_ctrl_recv() (no upper bound). When data_len exceeds CONFIG_WIREGUARD_BUF_LEN — e.g. when the buffer length is lowered below the link MTU, on links with MTU above the buffer size, or via reassembled IPv4/IPv6 fragments that exceed it — the underlying memcpy writes past the end of the pool buffer, an out-of-bounds write (CWE-787). The overflow occurs before the Poly1305 authentication check, so it requires only a valid receiver session index rather than a valid authenticator, and is reachable by a malicious or compromised peer (or an on-path attacker driving an established session) over the network, yielding remote memory corruption and at minimum a reliable denial of service. The defect was present in the WireGuard implementation shipped in Zephyr 4.4.0. The fix adds an explicit data_len > CONFIG_WIREGUARD_BUF_LEN rejection and corrects the linearize call to pass net_buf_max_len(buf) as the destination capacity. |
| The nRF70 Wi-Fi driver's power-save event handler nrf_wifi_event_proc_get_power_save_info() in drivers/wifi/nrf_wifi/src/wifi_mgmt.c copied TWT (Target Wake Time) flow entries from an nrf_wifi_umac_event_power_save_info event into the fixed-size twt_flows[WIFI_MAX_TWT_FLOWS] (8-element) array of a caller-supplied struct wifi_ps_config, looping over event-provided num_twt_flows without validating it against WIFI_MAX_TWT_FLOWS or checking event_len. When num_twt_flows exceeds 8, the handler writes past the destination array (which is typically on the caller's stack, e.g. the wifi ps shell command) -- an out-of-bounds write of ~40-byte TWT entries -- and reads twt_flow_info[i] past the event buffer. The event is delivered by the nRF70 co-processor firmware in response to a host-initiated power-save GET, so reaching the overflow requires the firmware to emit a malformed or out-of-range event; the trust boundary is host-to-trusted-coprocessor rather than a direct remote-AP write, with over-the-air influence on the flow count being indirect and bounded by the 3-bit TWT flow-id space. Affected: builds with CONFIG_NRF70_STA_MODE on releases through v4.4.0. The fix rejects events with num_twt_flows > WIFI_MAX_TWT_FLOWS or with event_len shorter than the claimed entries, and adds a NULL check on the caller buffer. |
| In Zephyr's experimental USB host stack (CONFIG_USB_HOST_STACK), usbh_device_disconnect() (subsys/usb/host/usbh_device.c) freed the root usb_device slab object without clearing the cached pointer ctx->root. The bus removal handler dev_removed_handler() (subsys/usb/host/usbh_core.c) decides what to tear down solely from ctx->root, checking only that it is non-NULL.
Because UHC controller drivers (e.g. uhc_max3421e, uhc_mcux_common) synthesize UHC_EVT_DEV_REMOVED directly from physical bus line state with no debounce or state guard, an attacker with physical USB access (or a rogue device that bounces its connection) can deliver a second device-removed event after a root device disconnect. The handler then re-enters usbh_device_disconnect() with the dangling pointer, locking a mutex inside the freed object (use-after-free), removing the freed node from the device list, and calling k_mem_slab_free() on the already-freed block (double-free). If the slab block has been reissued to a newly attached device in between, this corrupts a live object.
Impact is denial of service (crash) and memory corruption; the attack vector is physical/local. The flaw was introduced in v4.4.0 by the connect/disconnect refactor and is fixed by clearing ctx->root in usbh_device_disconnect() before freeing. |
| The Nuvoton NuMaker HSUSBD USB device-controller driver (drivers/usb/udc/udc_numaker.c) armed the control Data IN stage unconditionally (base->CEPTXCNT = len in numaker_hsusbd_ep_trigger). Because the HSUSBD hardware cannot disarm a control Data IN already armed for a previous transfer, a USB host that cancels an in-flight control transfer (timeout) and then issues a new SETUP packet can drive the driver out of sync: stale data may be transmitted in the new transfer and the control endpoint can become permanently stuck NAK'ing every subsequent control transfer.
A malicious or buggy host (physical/adjacent attacker driving the bus) can repeatedly cancel-and-re-SETUP to wedge the device's USB control endpoint, denying service to the device's USB function (the device stops enumerating/responding on the control pipe) until a USB reset or re-plug. The flaw is an availability-only denial of service; the FIFO copy loops (bounded by net_buf length and the hardware BUFFULL flag) and the net_buf lifecycle are independent of the arming desync, so there is no out-of-bounds access, use-after-free, or information leak.
The fix monitors the IN-token and new-SETUP events (k_event) and only arms control Data IN when an IN token is present and no new SETUP has arrived, cancelling the current transfer on a new SETUP. Affects boards using the Nuvoton NuMaker HSUSBD controller (CONFIG_UDC_NUMAKER with DT_HAS_NUVOTON_NUMAKER_HSUSBD_ENABLED); shipped in v4.4.0. |
| The Bluetooth BAP Broadcast Assistant GATT client in subsys/bluetooth/audio/bap_broadcast_assistant.c reassembled remote Broadcast Receive State data into a single file-static net_buf_simple (att_buf, BT_ATT_MAX_ATTRIBUTE_LEN = 512 bytes) shared by all connection instances, while the BUSY flag, long-read handle, and reset/offset state were per-connection.
When the device acts as a Broadcast Assistant connected to multiple Scan Delegator peripherals, notification and long-read callbacks from different connections interleave on the shared buffer: the append in notify_handler (net_buf_simple_add_mem at the not-busy branch) performs no tailroom check, so receive-state notifications from two or more delegators accumulate on the same 512-byte buffer and, with a sufficiently large configured ATT MTU (BT_L2CAP_TX_MTU up to 2000) and two-to-three concurrent connections, write past the buffer into adjacent .bss (net_buf_simple_add only asserts in debug builds).
Even below the overflow threshold, one connection's net_buf_simple_reset zeroes the shared length while another connection's reassembly and GATT read offset are in flight, mixing one peer's data into another's parse. A malicious or compromised Scan Delegator (or two colluding peers) over BLE can trigger this, causing out-of-bounds writes (memory corruption / denial of service) and cross-connection data corruption.
The fix moves the buffer into the per-connection instance struct so each connection reassembles into its own buffer. Affects Zephyr releases shipping the Broadcast Assistant with the shared buffer, including v4.4.0 and earlier. |
| Zephyr's DNS resolver (subsys/net/lib/dns) parses resource records from DNS responses in dns_unpack_answer(), which validated only the fixed RR header (type, class, TTL, rdlength) and accepted any attacker-declared rdlength, including one extending past the end of the received datagram. The TXT and SRV consumers in dns_validate_record() (resolve.c) then read up to rdlength bytes (clamped only to a record-type maximum such as DNS_MAX_TEXT_SIZE, default 64, not to the packet) from the receive buffer via memcpy without their own bounds check, and pass the result to the application's resolve callback. A malicious or spoofed DNS server, an on-path attacker forging UDP DNS replies, or (with mDNS/LLMNR enabled) any LAN node can craft a truncated TXT or SRV response that causes an out-of-bounds read of adjacent receive-pool memory; the disclosed stale bytes (residual contents of prior DNS packets / uninitialized pool memory) are returned to the application as TXT/SRV record contents, an information leak, and may in some configurations cross the allocation boundary and fault, causing a denial of service. The read is bounded (~64 bytes for TXT, ~6 for SRV) and read-only (no write). The fix rejects any record whose declared rdata extends past dns_msg->msg_size at the single chokepoint in dns_unpack_answer(). Affected: v4.3.0 and v4.4.0. |
